You can change your BitBox device password in the BitBoxApp if you know the current password. You enter the current and new passwords on the BitBox itself, without resetting the device or restoring your wallet.

The device password unlocks your BitBox. Changing it keeps the same wallet and does not move your funds or change an optional passphrase. Your existing wallet backups remain valid; you do not need to replace them because you changed the device password.

Before you start

  • Use the latest stable BitBoxApp from the official download page.
  • Keep your BitBox firmware up to date. Direct password changes require firmware 9.25.0 or later; follow Update your BitBox firmware if needed.
  • Have your BitBox and its current device password ready. The steps below use the BitBoxApp on a computer with the BitBox connected by USB.

If you have forgotten the current password, follow Forgot your BitBox device password? instead. Do not reset the device or keep guessing: first check that you have the correct wallet backup and any exact optional passphrase needed for recovery.

A normal password change does not require your recovery words or microSD backup. Keep the backup securely stored, and never send passwords, recovery words, backup files or an optional passphrase to Support.

Choose and enter your new password

Your device password can contain uppercase letters (A–Z), lowercase letters (a–z) and numbers (0–9). Uppercase and lowercase letters are different. Spaces and special characters are not available for the device password.

On a password-entry screen, tap the touch sensor along the top edge of the BitBox, directly above the label in the center, to switch keyboard modes. The label shows the mode you will switch to: abc for lowercase letters, ABC for uppercase letters and 123 for numbers. Each tap moves to the next mode in the cycle: lowercase → uppercase → numbers → lowercase. You can switch modes while entering a password.

The three screens below show the available modes. Your BitBox may start in a different mode. To choose a character, tap the bottom edge below the group containing it, then continue selecting the smaller group until you can select the individual character.

Lowercase letters on the BitBox password-entry screen, with ABC at the top to switch to uppercase
Lowercase letters: tap above ABC to switch to uppercase.
Uppercase letters on the BitBox password-entry screen, with 123 at the top to switch to numbers
Uppercase letters: tap above 123 to switch to numbers.
Numbers on the BitBox password-entry screen, with abc at the top to switch to lowercase
Numbers: tap above abc to switch to lowercase.

Change your device password

Use the app to start the change, then complete the password prompts with the BitBox's touch controls. The screenshots show the English desktop interface.

  1. Open the BitBoxApp, connect your BitBox by USB and unlock it by entering the current device password on the BitBox.
  2. In the BitBoxApp, select Settings in the left sidebar, then Manage device. Scroll to the Device settings section.
Change device password in the Device settings section of Manage device
  1. Select Change device password. The app asks you to follow the instructions on your BitBox.
BitBoxApp asking you to follow the instructions on your BitBox
  1. On the BitBox, confirm Proceed to change password? only if you intentionally started the change.
  2. At Unlock device, enter your current device password again on the BitBox. This second prompt verifies the existing password before it can be replaced. If you are unsure of it or see a remaining-attempt warning, stop rather than guessing.
  3. At Set password, enter the new device password on the BitBox and confirm the entry.
  4. At Repeat password, enter that same new password again and confirm it. If the two entries match but contain fewer than four characters, the device shows an additional short-password warning. If you see this warning, cancel the change and choose a stronger password.
  5. Keep the BitBox connected when it displays Success. This message follows the matching password entries; the password change still needs to finish. Wait for the BitBoxApp to display Password changed successfully, then select OK.
Password changed successfully confirmation in the BitBoxApp

Confirm the result

The app's Password changed successfully confirmation means the change has completed. Use the new device password the next time you unlock this BitBox; the old one has been replaced.

Keep your existing wallet backups secure and retain the exact optional passphrase separately if you use one. Changing the device password does not replace that recovery information.

If the change does not complete

The password-change option is unavailable

Update the BitBoxApp and check for a firmware update for your device. Firmware older than 9.25.0 does not support this direct change. If the option remains unavailable after updating, contact Support with your app and firmware versions. Do not reset the wallet just to make the option appear.

The device shows “Wrong password”

The current device password was not accepted. Incorrect current-password entries during this change count toward the device's unlock-attempt limit, just as they do when unlocking it.

Do not keep guessing the current password

Ten failed device-password attempts trigger an automatic reset, erasing the wallet data on the device. Follow any remaining-attempt warning. If you cannot confidently enter the current password, stop and use the forgotten-password guide to check your recovery prerequisites before taking further action.

 

The device shows “Passwords do not match”

The two new password entries differed. This attempt stopped before saving a new password, so the previous device password remains in use. Start the password-change procedure again and enter the same intended new password at both new-password prompts.

You canceled, lost the connection or saw another error

Canceling before the new password is saved leaves the existing password in place. An interrupted connection or unexpected error does not establish whether the change completed. Do not assume the early device Success message proves that it did, and do not repeatedly try different passwords or reset the device to resolve the uncertainty.

Contact BitBox Support if you cannot determine the result or complete the change. Include your BitBox model, computer operating system, BitBoxApp and firmware versions, the step where it stopped, and the exact error text. Never include passwords, recovery words, backup files, private keys, an optional passphrase or screenshots containing them.